Suntec E4 NC 1069

Suntec SKU: PHP54068
Suntec E4 NC 1069-Fuel Pump

Suntec E4 NC 1069

Suntec SKU: PHP54068
Prix régulier £317.96
/

  • Free UK Shipping (Mainland - Over £500)
  • Safe & Secure Checkout
  • Full Manufacturers Warranty

Rotation: Anti Clockwise
Nozzle Port: Left
Hub: 54mm
Shaft Diameter: 11mm

 

The SUNTEC E 1069 oil pump is specially designed for heavy oil applications: it is fitted with a special type shaft seal resisting high temperature and with a preheater location to render cold starting easier.

 

APPLICATIONS

- Heavy oil.
- One or two-pipe system
- Pump associated with in-line solenoid valve to assure cut-off function

 

PREHEATING FACILITY

The body of the E 1069 unit includes a drilling to accept an electric preheater. This cavity has been designed to give maximum heat transfer from the heater to the oil in the pump without there being direct contact between the heater cartridge and the oil.

The heating cartridge can be fitted either by right-hand side or by left-hand side. The preheater should be connected for a period of time prior to starting the pump. When the right temperature is reached, it can be switched off or left permanently switched on to maintain fluid oil in the pump during the periodic burner shut-downs. The oil supply, pipes and filters must be separately heated.

 

PUMP OPERATING PRINCIPLE

The gear set draws oil from the tank through the built-in filter and transfers it to the valve that regulates the oil pressure to the nozzle line.

All oil that does not go through the nozzle line will be dumped through the valve back to the return line in two pipe installation or, if it is a one-pipe installation, back to the suction port in the gear-set. In that case, the by-pass plug must be removed from the return port and the return port sealed by steel plug and washer.

During starting period when the gear-set speed is increasing, all the oil passes through a special flat on the piston, back to the return. Once the speed reaches a certain value and the flow can no longer pass through this flat, then the pressure increases rapidly overcoming the valve spring force and opens the valve.

 

Bleed:

During the starting period, air is purged through the nozzle line : the by-pass hole of the nozzle plug allows air to pass to the nozzle line without opening of the regulator valve.
For the first start up, bleeding can be accelerated by loosening the plug in the pressure gauge port.



Suntec E4 NC 1069 Technical Datasheet


Suntec E4 NC 1069 Exploded View

Ce site est protégé par reCAPTCHA, et la Politique de confidentialité et les Conditions d'utilisation de Google s'appliquent.

Plus de Oil Pumps
Danfoss Red Cartidge Filter + O-Ring BFP 071N0064-Fuel Pump
Danfoss Red Cartidge Filter BFP Diamond - 071N0064
Danfoss
£3.50
Danfoss Bypass Screw For BFP Pumps 071N0041
Danfoss
£7.50
Réduit
Danfoss BFP Pump Replacement Filter - 071N0063-Fuel Pump
Danfoss BFP11 Pump Drum Type Filter - 071N0063
Danfoss
Prix réduit £9.99 Prix régulier £16.00 Épargnez 38%
Riello Pump Seal
Riello RDB Oil Pump Seal - 3020443
Riello
£24.10
Danfoss BFP Replacement Coil T85 - 071N1006
Danfoss
£24.30
Danfoss BFP Valve Housing Stem - 071N0050-Fuel Pump
Danfoss BFP Valve Housing Stem - 071N0050
Danfoss
£28.35
Vu récemment